Control shot: 8.5" penetration, with 4.5" cavity measured at widest section.
The core has completely separated from jacket.
5.7x28 S4 15% gel test
5.7x28 ULTRA RAPTOR Level II Vest 10% 14"x6" gel block test
Level lla vest shot: 8.0" penetration, with 3.3" cavity at widest section.
Complete separation of the core from the jacket.
The jacket has completely fragmented in to fine shrapnel.
Elite Ammunition S4 Ultra RapTOR (5.7x28mm) vs a 10lb Pork Shoulder
5.7x28mm Comparison; SS192 vs EA S4 Ultra RapTOR
ProtecTOR
Round: ProtecTOR
Type: 40 grain V-max
Application: Self Defense / Law Enforcement / Civilain designed to provide good penetration with fragmentation while reducing chances of over penetration.
Capable of defeating 30 layers of Kevlar while still penetrating 9.0 inches of 10% ballistic gelatin
FiveseveN Pistol2,092fps - 389 Ft-Lb’s
FsN USG Pistol 15 feet
5.7x28 ProtecTOR 10% 13"x6" gel block test
Control shot.17cal BB 4.5" penetration
Penetrated all 13", and created 3.3" cavity measured at widest section.
FsN USG Pistol 15 feet
5.7x28 ProtecTOR 10% gel test
Control shot.17cal BB 4.5" penetration
Point Blank level II Vest
Penetration 9.0", and created 1.7" cavity measured at widest section
5.7x28 ProtecTOR 10% 13"x6" gel block test
Control shot.17cal BB4.5" penetration
Penetrated all 13", and created 3.3" cavity measured at widest section.
5.7x28 ProtecTOR 15% Gel Test Audio Malfunctioned
5.7x28 ProtecTOR One Level II Vest 15% Gel Test Audio Malfunctioned
Protector vs Melon
ProtecTOR plywood barrier, water jug and hollow core door
EA ProtecTOR II
This round WILL NOT replace the the original ProtecTOR.
EA is proud to announce our ProtecTOR II!
Using Combined Technology's 50gr Ballistic Silvertip Bullet.[
FsN 1790 fps 356 ft.lbs
EA ProtecTOR III
Bullet: 46gr JHP
FsN 1850 fps 350 ft-lbs
Application:Self Defense / CCW
PenetraTOR
Round: PenetraTOR
Type: 55 grain Mil Spec FMJBT
Application: Law Enforcement / Military
Ideal for Military and Law Enforcement personal requiring a NATO spec FMJ round
Capable of defeating 30 layers of Kevlar while still penetrating 11.5 inches of 10% ballistic gelatin
FiveseveN Pistol1,800 fps - 385 Ft-Lb’s
P902,150 fps - 560 Ft-Lb’s
PS902,300 fps - 660 Ft-Lb’s
FsN USG Pistol 15 feet
5.7x28 PenetraTOR10% 13"x6" gel block test
Control shot:.17cal BB 3.2" penetration
full penetration of block
FsN USG Pistol 15 feet
5.7x28 PenetraTOR USG Level ll vest10% 13"x6" gel block test
Controlshot:.17calBB3.2"penetration
Penetrated the vest and11.5" of gel block
SinTOR
The SinTOR uses SinterFire's 36gr compressed metal bullet. Ideal for live fire training in Shoot Houses.
"Insert blovaiting here" for those who miss it.
FsN1850 fps275 ft-lbs
P902254 fps406 ft-lbs
PS902489 fps495 ft-lbs
I worked with Doug at SinterFire since there is a great demand for this type of bullet loaded into the 5.7. In fact an upcoming SWAT competition where teams want to use their 5.7 platform but must use a SinterFire type projectile helped move this forward quickly. I spent all day today with final testing.
VarminTOR
36 Grain Frangible Barnes Varmint Grenade
Round: VarminTORType: 36 grain frangible HP Application: Law Enforcement / Civilian pest eradication (nutria) It is important to note that these bullet fragments rarely exit the animal.
FsN USG Pistol 15 feet 5.7x28 VarminTOR 10% 13"x6" gel block test Control shot.17cal BB 4.5" penetration Penetrated 13” into gel block with heavy fragmentation.
This round was not tested against body armor
Varmintor vs Melon
EA VarminTOR II
Bullet Type: 50gr Sierra Blitz King
Application: Low velocity boarder line Sub Sonic round for light varmint hunting and “Walking” round
FiveseveN Pistol 1000 fps 111 ft-lbs
P90 1250 fps174 ft-lbs
PS90 1445 fps232 ft-lbs
IlluminaTOR
Fun with Illuminator
X-TerminaTOR
Round: X-terminaTORType: 45 grain TSX Application: Law enforcement / Military / Civilian Round is designed for small to medium sized game under 100 yards. Capable of defeating 30 layers of Kevlar while still penetrating 11.5 inches of 10% ballistic gelatin"
FsN USG Pistol 15 feet 5.7x28 X-terminaTOR 15% 13"x6" gel block test Control shot.17cal BB 3.2" penetration: Full penetration, with 3.0" cavity measured at widest section.
FsN USG Pistol 15 feet 5.7x28 X-terminaTOR USG Level ll vest15% 13"x6" gel block testControl shot.17cal BB 3.2" penetration: Point Blank level II and 11.5" of gel block before exiting. The cavity has measured 2.7" at widest section.
You asked for it, and we've delivered.
The Elite Ammunition X-TerminaTOR.
This cartridges pushes a 45 grain Barnes TSX FB bullet at more than 1,900
fps from the pistol (375 Ft.Lbs of energy), and 2,500 fps from the PS90,
which equates to 625 Ft.Lbs or kinetic energy at the muzzle.
Capitalizing on Barnes legendary bullet design, quality control, and
terminal expansion, Elite Ammunition has reached another milestone in the
war on wildlife with the X-TerminaTOR.
Penetration through 15% ballistics gelatin exceeds 14", from the pistol,
and bullet expansion is greater than 50% of the original diameter.From
the PS90, the bullet penetrates a full 21" of 15% ballistics gelatin
while expanding more than 75% of the original diameter.Weight retention
is more than 99.5%, even after passing through bone and connective tissue.
The X-TerminaTOR comes shipped in a 50 round plastic Berry's Bullet box,
at no additional charge, protecting the X-TerminaTOR during even the most
grueling of hunts.
Never before has a more effective small to medium game hunting round been
developed in 5.7x28mm; again proving that Elite Ammunition truly is "The
Result of Perfection."
5.7x28 ExterminaTORUSG 15% 13"x6" gel block test
Control shot:.17cal BB3.2" penetration
full penetration, with 3.0" cavity measured at widest section.
Level ll vest shot:bullet has penetrated the vest and 11.5" of gell block before exiting.The cavity has measured 2.7" at widest section.
5.7x28 ExterminaTOR AR57 15% gel test
Note that the blocks have being cut from the top and the side, so the extend of the demmage can be seen more clearly.
QuieTOR 5.5
Mil Spec 55 Grain FMJ
Round: QuieTOR Type: 55 grain Mil Spec FMJBT Application: Law Enforcement / MilitaryIdeal for Military and Law Enforcement personal requiring a subsonic round.
The Elite Subsonic are a great round. Here we are with a polished Jarvis barrel chamber, a GemTech Silencer and Elite QuieTor Ammo. - A winning combo.
QuieTOR 10.5
Mil Spec 55 Grain FMJ
Round: QuieTORType: 55 grain Mil Spec FMJBT Application: Law Enforcement / MilitaryIdeal for Military and Law Enforcement personal requiring a subsonic round.
Round: QuieTORType: 55 grain Mil Spec FMJBT Application: Law Enforcement / MilitaryIdeal for Military and Law Enforcement personal requiring a subsonic round.
EA QuieTOR, Self Loaded Subsonic, and EA PenetraTOR
IlluminaTOR
5.7x28 IlluminaTOR AR57 15% gel test
EA 165gr +P* 10mm Load
EA 165gr +P* 10mm Load
Warning if your looking for watered down 40 Short and Weak load this is not for you.
165gr +P* MG HP Starline Nickel Brass
Loads chronographed at 80 degrees F.
S&W 610 6.5 barrel 1460 fps 787 ft. lbs energy
Witness full sized 5 barrel comped 1400 fps 723 ft. lbs energy
Witness Compact 3.5 barrel 1270 fps 591 ft. lbs energy
This round was not tested against body armor
* EA recognizes that SAAMI does not officially list a +P rating for 10mm. EA does though to stress the fact that these are full power 10mm loads and recommends both higher rated recoil and firing pin springs
EA 10MM+P 165gr MG Meat 5.26.10
EA 10MM +P 165gr MG Meat Dissection Part 1 5.26.10
EA 10MM +P 165gr MG Meat Dissection Part 2 5.26.10
EA 10MM+P 165gr MG Mellon 5.26.10
EA 10mm+P* 200gr MG CMJ
200gr +P* MG CMJ Starline Nickel Brass
Loads chronographed at 80 degrees F.
S&W 610 6.5 barrel 1295 fps 745 ft. lbs energy
Witness full sized 5 barrel comped 1290 fps 739 ft. lbs energy
This round was not tested against body armor
* EA recognizes that SAAMI does not officially list a +P rating for 10mm. EA does though to stress the fact that these are full power 10mm loads and recommends both higher rated recoil and firing pin springs. EA does not recommend using this ammunition in compact or polymer auto pistols.
Meat shooting vid
Dissection
EA 45acp 230gr+P MG JHP
EA 45acp 230gr +P* JHP
MG HP
Starline Nickel Brass
Loads chronographed at 70 degrees F.
Colt 1911 5.5 barrel 950 fps 461 ft. lbs energy
Colt Combat Commander 4.5 barrel 925 fps 437 ft. lbs energy
This round was not tested against body armor
*45ACP+P ammo is externally/dimensionally identical to 45 ACP ammo and can be fired in any 45 acp firearm that is in normal operating condition. However, the greater pressures and power of the +P ammo will give you greater slide velocity and if you are going to shoot more than a box or two of +P ammo, you should consider replacing your recoil spring with a extra power Spring that gives roughly 4 to 6 lbs more spring weight than factory stock springs.
EA 45acp+P 230gr MG JHP meat
EA 45acp+P 230gr MG JHP dissection
Trident .308 147gr XBT Loaded Ammunition
147gr Banded Solid Extreme Boat Tail
New Winchester Nickel Brass
Bench Rest Primer
2850fps. 2652Ft. Lbs energy
26 inch barrel 70 Degrees F.
20 Rounds per box
Case Prep
1)Sized
2)Debured
3)Chamfered
4)Trimmed
5)Primed
Powder Charge
1)Hand dropped
2)Only one lot used for each batch of 100 rounds
Bullet
1)Seated by hand
2)Crimped
3)COAL Target 2.810
Each round is checked for COAL.Then the 100 lots are grouped/packaged according to COAL.
Trident .308147grXBT Bullet
Turned Homogenous Copper Zinc alloy, not beryllium copper bullets. Extremely accurate with our signatureExtreme Boat Tail that drive up BC, and friction reducing cuts allowing for higher velocity and lower pressure.
50 Bullets per Box
THIS IS NOT LOADED AMMUNITION
EA Adjustable Night Sights
FYI SEND ME ONLY YOUR SLIDE, REPEAT SEND ME ONLY YOUR SLIDE!
When you send your slide you must include all your contact information including email and Forum ID.
Cost is $265.00
Please ship your slide in a way that generates a tracking number. This also includes insurance.
Here is the break down. Due to demand for this style of sight here they are!
These are custom three dot sights.
Front and Rear sights are used in part to make the replacement sights.
Any one who has taken a USG slide cover off knows the rear sight holds all sorts of small stuff in the slide.
So things modified to point that if you return to old sites must be replaced.
1) Front site
2) Rear site
Turn around time will be three weeks MINIMUM.
We can change your fixed over to adjustable night sights. There are additional parts needed for the conversion. The cost is,
$265.00Night sights
$95.00Rear adjustable sight assembly from FN
$25.00Front site blade, adj. uses different blade.
$5.00New slide cover
$390.00 Total +S&H Installation included.
$340.00 Total + S&H If Fixed Sights NOT Returned with slide.
If your current cover and fixed sights are in good condition $50.00 credit for them.
EA Fixed Night Sights
We replace your fixed sights with fixed night sights. Front dot is green and the rear dots are yellow. All have white outlines.
FYI SEND ME ONLY YOUR SLIDE, REPEAT SEND ME ONLY YOUR SLIDE!
EA FsN Heavy Duty 20 pound Recoil Spring
This spring replaces your worn out or under powered 18 pound factory spring.
MSM
Elite Ammunition is proud to announce our EA Mini Slide Mount [/size]patent pending [size=150]picatinnyred dot sight base for the USG. It is easily installed by the end user, uses existing hardware and does not alter your gun in anyway. Takes just minutes to change back over to your factory sight.
Rail has a site channel and dots machined into the base so you can still use the iron sights as a back up.
Base is constructed of Aluminum and is anodized black. Max weight of red dot sight is 2.5oz.
Elite Ammunition 5.7x28 Extra Power Springs
In stock, but in very limited quantities.
So once they are gone
They will be gone
Elite Ammunition 5.7x28 Extra Power Springs.
Our springs are approximately 30% stronger than the factory springs, are made from a custom alloy which is a cross between stainless steel and chrome silicon; which provide extreme life and don't allow spring-set.The extra power ensures positive feeding during periods of extreme use when the weapon may be filthy, full of mud, debris, water, or dead people guts.They are also nearly impervious to oxidation and require a minimum of lubrication due to its metallurgy.
USG/IOM Pistol Mag Springs $5.95 each + S&H
EA Go NoGo Gauge
EA Dillon 550 5.7x28 Shell Plates
Elite Ammunition *DILLON 550 5.7x28 SHELL PLATES*
With your Shell Plates you will also receive 3 custom locator buttons.
EA Custom RCBS Trim Pro Plate
EA Custom RCBS Trim Pro Plate
Hornady40gr Blue Tip V-Max Bullets .224 Caliber pulled from SS197
Hornady40gr Blue Tip V-Max Bullets .224 Caliber pulled from SS197
Since the inception on the 5.7x28 fans of the round have asked, demanded, petitioned, begged, and pleaded for an inexpensive practice round. Well Elite Ammunition has taken one giant step in the direction. EA is excited to announce their new 5.7x28 adapter patent pending. This adapter allows you to create your own inexpensive practice rounds.
Here is what it is. The EA adapter looks like a standard piece of 5.7x28 brass. At first glance you notice it is made from stainless steel. Then you notice the large rifle primer pocket.
Here is how it works. First you use your hand priming tool of choice and seat a large rifle primer in the pocket. Then you select your projectile. Any 22cal air rifle pellet will work. Also to make things more interesting you can use 22cal 30gr muzzle loader lead bullets from Midway. Seat the pellet by hand by simply pushing it in. If you suffer from OCD it’s ok to seat the pellet on your loading press. Then load the round like you would any other and blast away. If you use a Lead free primer you can safely shoot indoors as long as you backstop can stop a high end air rifle pellet. Of course we recommend eye and hearing protection and save the beer for later. We didn’t but you should. Use a punch to knock out the old primer and repeat..223 version to follow.
Controll shot: 9.0" penetration before exiting the block. 3.3" cavity.
Level ll vest: 10" penetration with 2.3" cavity. No core separation. Slight deformation.
We PROUDLY Support
ALL ORDERS SHIP VIA FEDEX OR UPS ONLY
We MUST have a copy of your ID with Proof of age on File before your PISTOL ammunition order is processed and shipped. Please email Proof of Age to orders@eliteammunition.com NO EXCEPTIONS YOU MUST BE 21 TO ORDER PISTOL AMMUNITION
ALL Illinois Residents MUST provide a copy of their FOID Card before your ammunition order is processed and shipped. Also we can ONLY ship to the address shown on the FOID Card. If your FOID Card is not on file please email a copy to orders@eliteammunition.com and your order number must be included in the email.
All products are currently shipping in 4 to 6 weeks unless otherwise noted
Back Orders Accepted when noted
Illinois Residents MUST have a FOID Card on File with us before we ship your order and the FOID address MUST Match the Bill to & Shipping address on the order. WE DO NOT SHIP TO COOK COUNTY, ILLINOIS
Sorry we cannot ship to Cook County, Illinois or LA County, California ♦ Sorry we only ship ammunition to the Lower 48 States
Prices are subject to change ♦ In Stock orders ship out on Fridays
There will be a 3% Restock Fee for any orders cancelled within the first 48 Hours